http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/ en-us Gallery 2 RSS Module, version 1.1.8 Tue, 07 Apr 2026 22:30:50 +0000 120 http://www.europaowners.org/gallery2/d/51563-7/album169.jpg http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/ http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/28_G.jpg.html http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/28_G.jpg.html ]]> danbish photo Tue, 17 Nov 2009 23:39:28 +0000 http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0041.jpg.html http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0041.jpg.html
Others have said there's too much friction with this set up. I hope I don't have to change it, will leave it this way until taxi tests. ]]> danbish photo Tue, 17 Nov 2009 23:39:28 +0000 http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0025.jpg.html http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0025.jpg.html
Movement to full port and full starboard show the cord would tighten to prevent fouling should a cable break.]]> danbish photo Tue, 17 Nov 2009 23:39:28 +0000 http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0024.jpg.html http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0024.jpg.html ]]> danbish photo Tue, 17 Nov 2009 23:39:28 +0000 http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0022.jpg.html http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0022.jpg.html ]]> danbish photo Tue, 17 Nov 2009 23:39:28 +0000 http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0021.jpg.html http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0021.jpg.html
This one works just fine. Ace Hardware, 7 strands of twisted inside, plastic coated. Following photos show how it attaches and shows movement port to starboard.]]> danbish photo Tue, 17 Nov 2009 23:39:28 +0000 http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0020.jpg.html http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0020.jpg.html
Per the mod, you're supposed to install cables that run through the springs then around the base of the tail wheel spring. This cable was too thick, will try something else. ]]> danbish photo Tue, 17 Nov 2009 23:39:28 +0000 http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0006.jpg.html http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0006.jpg.html
Finished installation]]> danbish photo Tue, 17 Nov 2009 23:39:28 +0000 http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0005.jpg.html http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0005.jpg.html ]]> danbish photo Tue, 17 Nov 2009 23:39:28 +0000 http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0004.jpg.html http://www.europaowners.org/gallery2/v/DanBish/Rudder-Tailwheel/album169/DSCF0004.jpg.html
Rivets in, nearly finished.]]> danbish photo Tue, 17 Nov 2009 23:39:28 +0000