|
|
20141102_161000
template for new firewall.
Date: 11/02/2014
Views: 42744
|
|
|
photo (1)
Bad pic, but shows the end of the reinforcement layups (port side).
Date: 08/20/2012
Views: 42523
|
|
|
|
dsc08620
Removal of the mono firewall.
Date: 04/14/2012
Views: 42406
|
|
|
dsc08619
Roap tied to the engine mount frame to hoist the airframe.
Date: 04/14/2012
Views: 41183
|
|
|
|
dsc08609
Underside of vents.
Date: 04/10/2012
Views: 41177
|
|
|
dsc08608
These will have to go. They are on top and I will remove them and put one vent on the bottom.
Date: 04/10/2012
Views: 40156
|
|
|
|
dsc08618
Block and tackle used to hoist the front of the aircraft to aid in creating a jig. This hoist reduces the weight to 25%.
Date: 04/14/2012
Views: 39743
|
|
|
20141102_161036
Everything looking good.
Date: 11/02/2014
Views: 39630
|
|
|
|
dsc08612
Unused Mono wheel components. I'll probably be selling these soon.
Date: 04/10/2012
Views: 36817
|
|
|
20141102_161049
20141102_161049.jpg
Date: 11/02/2014
Views: 36459
|
|
|
|
dsc08605
When I received the plane it had a few areas of this green tape. I guess it was going to be used as a release agent for some sort of jig fabrication. I have found that this 3M stuff works very well.
Date: 04/10/2012
Views: 35320
|
|
|
dsc08626
Put in a 2x4 in the main wing spar tunnel and located the pins. This was only used to aid in keeping the plane from tipping.
Date: 04/14/2012
Views: 35075
|
|
|
|
dsc08625
Cutting out one of the ribs for the airframe. Going to use the mono trailer as the foundation of the jig. This will make is easy to level the airframe when getting ready for the trr-gear conversion. How do you like my work bench?
Date: 04/14/2012
Views: 34709
|
|
|
dsc08613
Unused Mono wheel components. I'll probably be selling these soon.
Date: 04/10/2012
Views: 33548
|
|
|
|
dsc08603
Since I'm going to have to remove the mono wheel I dont have much of an edge to close in the big hole in the bottom. I'll have a better look at it once its a tri-gear.
Date: 04/10/2012
Views: 33109
|
|
|
20141102_152814
Drilling out the screw. It would move. I'm removing this plate to patch later.
Date: 11/02/2014
Views: 33025
|
|
|
|
dsc08614
Anybody know a easy way to remove this rust?
Date: 04/10/2012
Views: 32211
|
|
|
dsc08400
Very hard to work in the tunnel and I'm a small guy, 5'11“ 150#
Date: 03/25/2012
Views: 32101
|
|
|
|
Orange part created in turbocad and printed on a 3D printer from ABS. Printer is a Prusa i3 X, cost is around $300.
Orange part created in turbocad and printed on a 3D printer from ABS. Printer is a Prusa i3 X, cost is around $300.
Date: 04/03/2016
Views: 31916
|
|
|
dsc08627
The monowheel landing gear is in the up position and resting on the main wheel with some of the weight held by the block and tackle. This was taken just before putting on the braces to keep her from rolling. Been trying to get rid of that tv in the back
Date: 04/14/2012
Views: 31828
|
|
