| 
 | 
 
IMG_0047post
 
Walked down to the corner of the hanger to the next line of hangers where there is a WC.  This is what I saw to the Southeast.  Not looking good.  Went to the WC and cleaned up.  Looked even more threatening after the wash.  Decided to close up and go hom
 
Date: 07/08/2010
 
Views: 4306
 
 
 | 
 | 
 | 
 
DSC00889
 
Date: 04/15/2005
 
Views: 4816
 
 
 | 
 | 
| 
 | 
 
IMG_7529ann
 
The new BSPP (British Standard Pipe Parallel) banjo bolts finally arrived from Speed Flow of Australia last week.  Due to a death in the family and illnesses, I haven't gotten back to working on the Europa for several weeks.  But I did today.  I had also 
 
Date: 04/18/2010
 
Views: 4286
 
 
 | 
 | 
 | 
 
DSCN8266
 
Date: 09/18/2010
 
Views: 6693
 
 
 | 
 | 
| 
 | 
 
Front fuse conduit run 4.
 
Date: 08/20/2010
 
Views: 7690
 
 
 | 
 | 
 | 
 
G_PTAG_crossing_the_Mediterranean_with_me
 
Date: 07/04/2009
 
Views: 5604
 
 
 | 
 | 
| 
 | 
 
Fin cap 5.
 
Date: 03/22/2009
 
Views: 6596
 
 
 | 
 | 
 | 
 
Door sill conduit run 8.
 
Date: 08/10/2010
 
Views: 6000
 
 
 | 
 | 
| 
 | 
 
IMG_0001
 
Date: 03/22/2007
 
Views: 5551
 
 
 | 
 | 
 | 
 
IMG_5245ann
 
Date: 06/13/2009
 
Views: 4642
 
 
 | 
 | 
| 
 | 
 
112302_cowelwhite
 
Date: 12/31/1969
 
Views: 4106
 
 
 | 
 | 
 | 
 
CH37_23
 
Date: 11/29/1999
 
Views: 8050
 
 
 | 
 | 
| 
 | 
 
IMG_0037
 
More retraction tests.  Closer, but still won't quite go into up lock.  Maybe 1/4" (0.635 cm) from engaging.  Back under for a couple more hours before I finally see where the blue from the fitting is rubbing on the side of the tunnel where the seat 
 
Date: 07/07/2010
 
Views: 5201
 
 
 | 
 | 
 | 
 
Glass in reinforcement
 
Date: 11/27/2013
 
Views: 6541
 
 
 | 
 | 
| 
 | 
 
IMG_0045
 
Date: 03/20/2007
 
Views: 5534
 
 
 | 
 | 
 | 
 
IMG_0174post
 
Date: 09/06/2010
 
Views: 4076
 
 
 | 
 | 
| 
 | 
 
020602_lense_mold
 
Date: 12/31/1969
 
Views: 5264
 
 
 | 
 | 
 | 
 
13112003201315_G
 
Date: 12/31/1969
 
Views: 3501
 
 
 | 
 | 
| 
 | 
 
Klaus goes for a ride 1
 
Date: 10/25/2009
 
Views: 7048
 
 
 | 
 | 
 | 
 
IMG_7230
 
It was determined that a 1/4 in (6.4 mm) thick piece of rigid urethane foam topped with cork was needed to support the front "ledge" of the tank so it wouldn't sag.
 
Date: 01/26/2014
 
Views: 9183
 
 
 | 
 |