|
dsc08612
Unused Mono wheel components. I'll probably be selling these soon.
Date: 04/10/2012
Views: 10326
|
|
|
dsc08965
Port side after layups and peel ply removed. Notice shape of hole for the angle of the LG socket. I wrapped the LG socket with sandpaper and used it to form the hole.
Date: 10/01/2012
Views: 8517
|
|
|
dsc08403
Bill helping me out!
Date: 03/25/2012
Views: 8442
|
|
|
dsc09024
I was really anal about keeping the socket holes tight. This proved to be more work than it was worth and was fighting the tight fit when it came to locating the axles. Do yourself a favor and just make them a little bigger, 1/8 or so. This gap will be
Date: 01/22/2013
Views: 6983
|
|
|
dsc09045
Uncle Kim at work. We would tilt to starboard to work on the port side vice versa.
Date: 01/23/2013
Views: 7786
|
|
|
nex_2014_01_25_05
My lovely bride helping us out. Notice the jig is the mono wheel trailer.
Date: 01/25/2014
Views: 6142
|
|
|
dsc09019
Trash can is the best way to hold the landing gear legs.
Date: 01/10/2013
Views: 7007
|
|
|
nex_2014_01_12_07
Port side.
Date: 01/13/2014
Views: 6120
|
|
|
2012-08-18_19-58-15_689
Port side. Red highlighted area shows area with little reinforcement on inside. This is before I did the belly layup per the manual.
Date: 08/19/2012
Views: 9581
|
|
|
Actual part.
Actual part.
Date: 04/03/2016
Views: 11557
|
|
|
20141102_154450
Gear cover removed, now for removing the throttle box. This is all prep work to patch up the mono wheel hole.
Date: 11/02/2014
Views: 13400
|
|
|
p1000689
p1000689.jpg
Date: 03/12/2012
Views: 5958
|
|
|
p1000721
p1000721.jpg
Date: 03/12/2012
Views: 6105
|
|
|
dsc08627
The monowheel landing gear is in the up position and resting on the main wheel with some of the weight held by the block and tackle. This was taken just before putting on the braces to keep her from rolling. Been trying to get rid of that tv in the back
Date: 04/14/2012
Views: 8566
|
|
|
dsc08600
Thinking of modifying the mono wheel trailer as a jig to perform the tri-gear conversion.
Date: 04/10/2012
Views: 12073
|
|
|
p1000716
p1000716.jpg
Date: 03/12/2012
Views: 5531
|
|
|
p1000697
p1000697.jpg
Date: 03/12/2012
Views: 5714
|
|
|
dsc09022
Here you see I used bondo on the shims and screwed them down into the block. The shims made sure the guide was level. Also note the hole drilled in the Aluminum angle and the shim. This is where I fixed the guide for the curing stage to ensure nothing
Date: 01/22/2013
Views: 7461
|
|
|
dsc09029
Gear legs clamped in place, no toe in/out per Bud. You cant see it in the photo but I used a green tip .30 bullet as a homemade plum bob that was attached to dead center of the aluminum angle. This helped us keep the guide over the center line. Oh make
Date: 01/22/2013
Views: 6995
|
|
|
p1000472
p1000472.jpg
Date: 12/13/2011
Views: 11429
|
|