|
dsc09018
Started to make the axle jig. Used a simple setup of first taking large flat blocks of wood and caulking it to the floor somewhere over FS70. Then that allows me to fix the aluminum angle with a single screw once in its final position.
Date: 01/10/2013
Views: 8147
|
|
|
nex_2014_01_12_01
Bolt hole for LG port side filed to size.
Date: 01/13/2014
Views: 6005
|
|
|
20141102_161036
Everything looking good.
Date: 11/02/2014
Views: 11964
|
|
|
nex_2013_08_24_01
Stb. side ribs 3 and 4 epibond in place with the 3 layups on all sides. At this point I was getting faster at doing layups however I only did one side at a time.
Date: 08/25/2013
Views: 6368
|
|
|
dsc09076
Bottom layup of the port side.
Date: 01/26/2013
Views: 7108
|
|
|
DSC08799
Port side
Date: 06/05/2012
Views: 8283
|
|
|
dsc09073
Rib 2 template.
Date: 01/26/2013
Views: 7311
|
|
|
p1000686
p1000686.jpg
Date: 03/12/2012
Views: 5367
|
|
|
Orange part created in turbocad and printed on a 3D printer from ABS. Printer is a Prusa i3 X, cost is around $300.
Orange part created in turbocad and printed on a 3D printer from ABS. Printer is a Prusa i3 X, cost is around $300.
Date: 04/03/2016
Views: 17128
|
|
|
p1000702
p1000702.jpg
Date: 03/12/2012
Views: 5157
|
|
|
dsc09051
Mix it up Kim! FYI I hate this scale from aircraft spruce, it times out in one min if your plugged in or not. I would have to tap the scale while Kim mixed. We were using masks due to being in an enclosed area and I'm very allergic to the hardener (bumm
Date: 01/24/2013
Views: 7171
|
|
|
Actual part.
Actual part.
Date: 04/03/2016
Views: 11765
|
|
|
nex_2014_01_25_35
Dont judge me! You know you do it too. Anyways, was trying to see if my weight would cause the nose to come down. As you can see she likes being a tail dragger.
Date: 01/26/2014
Views: 8016
|
|
|
dsc08620
Removal of the mono firewall.
Date: 04/14/2012
Views: 13427
|
|
|
p1000695
p1000695.jpg
Date: 03/12/2012
Views: 5274
|
|
|
nex_2013_08_24_02
nex_2013_08_24_02.jpg
Date: 08/25/2013
Views: 5919
|
|
|
nex_2014_01_12_02
Rat's tail rasp works great here.
Date: 01/13/2014
Views: 5996
|
|
|
dsc09048
Template for the Stbd side. Note, you are not required per the manual to hook over the plywood with bid.
Date: 01/24/2013
Views: 7005
|
|
|
nex_2014_01_12_05
Port side top.
Date: 01/13/2014
Views: 6032
|
|
|
nex_2014_01_25_07
What a mess.
Date: 01/25/2014
Views: 6113
|
|