|
dsc09041
Port side guides being placed for layup.
Date: 01/23/2013
Views: 7366
|
|
|
dsc09054
Wetting out stbd side.
Date: 01/24/2013
Views: 6703
|
|
|
dsc09051
Mix it up Kim! FYI I hate this scale from aircraft spruce, it times out in one min if your plugged in or not. I would have to tap the scale while Kim mixed. We were using masks due to being in an enclosed area and I'm very allergic to the hardener (bumm
Date: 01/24/2013
Views: 7192
|
|
|
20141102_153539
Out. Ad you can see the screw is sill in the nut plate. it came out later.
Date: 11/02/2014
Views: 14202
|
|
|
nex_2014_01_25_01
Starboard side after Uni over ribs 3 and 4. Added Bid on the X to reinforce the cuts needed to get the Uni to lay flat. Also filled in Rib 1 air buble.
Date: 01/25/2014
Views: 6055
|
|
|
nex_2014_01_25_16
nex_2014_01_25_16.jpg
Date: 01/25/2014
Views: 6265
|
|
|
dsc09072
Here is a shot of the working angle. This was so much better than leaning over the edge. Kim's idea. Notice the heater behind Kim, this was key to keeping the temps even though the temps outside were in the 40's.
Date: 01/26/2013
Views: 7113
|
|
|
nex_2013_08_24_04
As you see here the port side is done with rib 3 and 4. I didn't have photos of doing the layups.
Date: 08/25/2013
Views: 6150
|
|
|
dsc08607
Starting to prep the bays for the tri-gear conversion.
Date: 04/10/2012
Views: 8166
|
|
|
photo
No pictures of the progress of putting in the LG layups on the port side. Here I am putting down the peel ply.
Date: 08/20/2012
Views: 13789
|
|
|
dsc08617
After removing the green tape.
Date: 04/14/2012
Views: 54291
|
|
|
dsc08662
The 10“ diameter from the pilot hole.
Date: 04/22/2012
Views: 11049
|
|
|
dsc09065
Stbd side peel ply removed.
Date: 01/25/2013
Views: 7535
|
|
|
nex_2014_01_12_02
Rat's tail rasp works great here.
Date: 01/13/2014
Views: 6019
|
|
|
dsc08630
Though this was a neat pic of the mono wheel in the retracted position.
Date: 04/14/2012
Views: 5917
|
|
|
dsc09057
Wetting out stbd side.
Date: 01/24/2013
Views: 6893
|
|
|
nex_2014_01_12_04
Port LG in place with bolt in.
Date: 01/13/2014
Views: 5986
|
|
|
nex_2013_08_24_03
nex_2013_08_24_03.jpg
Date: 08/25/2013
Views: 5871
|
|
|
dsc09024
I was really anal about keeping the socket holes tight. This proved to be more work than it was worth and was fighting the tight fit when it came to locating the axles. Do yourself a favor and just make them a little bigger, 1/8 or so. This gap will be
Date: 01/22/2013
Views: 7096
|
|
|
DSC08800
starboard side
Date: 06/05/2012
Views: 8552
|
|