<![CDATA[Wing rigging information.<br /> Y9-01-30]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/ en-us Gallery 2 RSS Module, version 1.1.8 Fri, 29 Mar 2024 10:08:57 +0000 120 http://www.europaowners.org/gallery2/d/31846-18/album162.jpg <![CDATA[Wing rigging information.<br /> Y9-01-30]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/ <![CDATA[Spar ramp 9.]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8786.JPG.html http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8786.JPG.html
Cleaned up, sanded smooth and flight ready.
Y10-12-11]]>
rparigoris photo Sun, 12 Dec 2010 05:23:51 +0000
<![CDATA[Spar ramp 8.]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8782.JPG.html http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8782.JPG.html
The void on ramp did get Aeropoxy / Flox with a taped G-10 form over it, but there was still a little void that got filled with JB KWIK weld.
Y10-12-11]]>
rparigoris photo Sun, 12 Dec 2010 00:26:33 +0000
<![CDATA[Port spar pin washer retention 3.]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8631.JPG.html http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8631.JPG.html
These washers are not going to fall off anytime soon!
Y10-11-09]]>
rparigoris photo Wed, 10 Nov 2010 07:27:34 +0000
<![CDATA[Port spar pin washer retention 2.]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8627.JPG.html http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8627.JPG.html
We JB KWIKed in place the shimming washers and the hardened Belleville like cone shaped washer with a G-10 washer on the outside figuring we would just fill between the G-10 washer and the cockpit module.
When Alan was cleaning up preparing for final bonding, the G-10 washer delaminated a little.
I decided to pull off the G-10 washer and 2 BID over the whole lot.
In order to keep the center of the forward most washer clear so the spar pin can rest on it, we JB KWIKed a socket in place that was covered in 3M 375 packaging tape.
We also used the G-10 washer that was taped to keep the 2 BID laying nice and flat in the center.
Y10-11-09]]>
rparigoris photo Wed, 10 Nov 2010 22:02:36 +0000
<![CDATA[Bonding Port lift pin sockets 20.]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8624.JPG.html http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8624.JPG.html
Aft Port lift pin socket fillet completed by Alan.
After cleaning up residue from the initial bond, two air pockets on the perimeter were discovered.
They were probed, fully opened and roughed up, scuff sanded, wet out and filled with Redux /Flox when doing the final fillet.
Y10-11-08]]>
rparigoris photo Mon, 08 Nov 2010 17:24:14 +0000
<![CDATA[Bonding Port lift pin sockets 19.]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8623.JPG.html http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8623.JPG.html
Front Port lift pin socket "super fillet' completed by Alan.
Y10-11-08]]>
rparigoris photo Mon, 08 Nov 2010 17:23:36 +0000
<![CDATA[Front Port fuse stiffening for lift socket 6.]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8619.JPG.html http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8619.JPG.html
3 BID and peel plied.
Y10-11-06]]>
rparigoris photo Sat, 06 Nov 2010 22:05:09 +0000
<![CDATA[Smooth rigging 8.]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8617.JPG.html http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8617.JPG.html
Port side gets a nice Tufnal spar guide.
Y10-11-06]]>
rparigoris photo Sat, 06 Nov 2010 22:07:24 +0000
<![CDATA[Front Port fuse stiffening for lift socket 5.]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8614.JPG.html http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8614.JPG.html
The front top edge needed a little more Flox than in other areas.
Y10-11-06]]>
rparigoris photo Sat, 06 Nov 2010 22:02:42 +0000
<![CDATA[Front Port fuse stiffening for lift socket 4.]]> http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8613.JPG.html http://www.europaowners.org/gallery2/v/Begin-06-2003/Wings+A+thru+Z/album162/DSCN8613.JPG.html
The fixture works great!
y10-11-06]]>
rparigoris photo Sat, 06 Nov 2010 22:00:20 +0000